Home > Socket Error > Bind Failed With Error 10038

Bind Failed With Error 10038

Contents

a TCP reset received from remote host). WSAEWOULDBLOCK 10035 Resource temporarily unavailable. Microsoft C description: Invalid argument. However, it is interchangeable in most cases, and all Windows Sockets functions that return one of these messages also specify WSAEAFNOSUPPORT. check over here

WSAECONNABORTED 10053 Software caused connection abort. No buffer space is available. An incorrect number of QoS FILTERSPECs were specified in the FLOWDESCRIPTOR. An invalid QoS provider-specific buffer.

Socket Error 10038

The connection was terminated due to a time-out or other failure. (Error code 10053)An established connection was aborted by the software in your host computer, possibly due to a data transmission An invalid or inconsistent flowspec was found in the QoS provider-specific buffer. See also: WSAECONNABORTED, WSAECONNRESET, WSAENETRESET WSAETOOMANYREFS (10059) Too many references; can't splice Berkeley description: too many references to some kernel-level object; the associated resource has run out. The socket cannot be connected. (Error code 10055)An operation on a socket could not be performed because the system lacked sufficient buffer space or because a queue was full.

In this case, the operation to close the socket will fail with this error if it cannot be completed immediately. SO_ACCEPTCONN, SO_DONTLINGER, SO_KEEPALIVE, SO_LINGER, SO_OOBINLINE and TCP_NODELAY are not supported on sockets of type SOCK_DGRAM. WSA_E_CANCELLED 10111 Call was canceled. Socket Error 10049 The socket has been shut down. (Error code 10058)A request to send data was disallowed because the socket had already been shut down in that direction with a previous shutdown call.

Detailed descriptions: the specific meanings that some WinSock functions have for some errors. Highlight the line of code. Here is a useable macro: #define MAKEWORD(low, high) ((WORD)(((BYTE)(low)) | (((WORD)((BYTE)(high))) << 8))) WinSock functions: WSAStartup(). [Go to Top] Errors in Numerical Order WSABASEERR (0) No Error WSAEINTR (10004) Interrupted system Is this safe to display MySQL query error in webpage if something went wrong?

The namelen parameter is incorrect. (Error code 10014)The system detected an invalid pointer address in attempting to use a pointer argument of a call. Socket Error 10054 Connection Reset By Peer The software caused a connection abort because there is no space on the socket's queue and the socket cannot receive further connections. Overlapped I/O operation is in progress. (Error code 997)The application has initiated an overlapped operation that cannot be completed immediately. WSAEADDRINUSE 10048 Address already in use.

What Is A Socket Error

You might also be touching the UI from a thread (another 'no-no') but we have not seen all of your code (what does OnEvent do, for instance). All sockets are created with an associated address family (that is, AF_INET for Internet Protocols) and a generic protocol type (that is, SOCK_STREAM). Socket Error 10038 How to deal with a very weak student? Socket Error 10053 WSAENETUNREACH 10051 Network is unreachable.

The network subsystem has failed. (Error code 10050)A socket operation encountered a dead network. check my blog asked 4 years ago viewed 2127 times active 4 years ago Related 0send(), returns Winsock Error 100381Bind Error 10038 with windows socket application in c4C++ Winsock Socket Error: 10038 (WSAENOTSOCK)0Winsock select Always be sure to allocate enough space. What to tell to a rejected candidate? Socket Error Codes Linux

A socket operation was attempted to an unreachable network. If you wish to continue this conversation start a new topic. The buf parameter is not completely contained in a valid part of the user address space. (Error code 10014)The buffer for incoming data contains an invalid pointer address. this content WinSock description: No equivalent.

Developer suggestions: Since there're only one corresponding protocol for each of the datagram and datastream socket types in the Internet address family, you should simply leave the value in the protocol Socket Error 10061 Connection Refused Not the answer you're looking for? The v1.1 WinSock specification doesn't list any errors for these functions.

WSAEPROTOTYPE 10041 Protocol wrong type for socket.

recv() & recvfrom(): socket not bound (for Dgram) or not yet connected (for Stream), or the requested length is zero (whether a length >32K is acceptable as a non-negative value is For example, this error is returned if sendto is called with the remote address of ADDR_ANY. Developer suggestions: Every application that uses non-blocking sockets must be prepared for this error on any call to the functions mentioned below. Socket Error 10022 WSA_QOS_RECEIVERS 11005 QoS receivers.

For unreliable protocols (for example, UDP) the excess data is lost; for reliable protocols, the data is retained by the service provider until it is successfully read by calling recv with WSA_QOS_POLICY_FAILURE 11011 QoS policy failure. The network cannot be reached from this host at this time. (Error code 10051)A socket operation was attempted to an unreachable network. have a peek at these guys The socket is not connected. (Error code 10057)A request to receive data was disallowed because the socket is not connected.

Detailed description: setsockopt(): WinSock generates this error if you try to set SO_KEEPALIVE on a connection that's already timed out. WSAEHOSTUNREACH 10065 No route to host. For example, you cannot use the ARPA Internet UDP protocol with type SOCK_STREAM. User suggestions: There are a number of things to check, that might help to identify why the failure occurred.

Clearly, this oversight was not intentional. A general QoS error. A QoS error occurred due to lack of resources. If so, treat this as a non-fatal error and ignore it, if possible.

User suggestions: see WSAHOST_NOT_FOUND for details. On a UPD-datagram socket this error would indicate that a previous send operation resulted in an ICMP "Port Unreachable" message. WSA_OPERATION_ABORTED 995 Overlapped operation aborted. The socket is already connected. (Error code 10056)A connect request was made on an already-connected socket.

Manage Cookies For information, see the Handling Winsock Errors topic. What is the sh -c command? WSAEINVALIDPROVIDER 10105 Service provider is invalid.

© Copyright 2017 gatoisland.com. All rights reserved.