Home > Error Codes > Bcr Control Initialize Error

Bcr Control Initialize Error

Contents

If the failure remains with the same slot, the magazine may be at fault. To check the overall operation of the device, run the wellness test from the RMI or OCP. The message shows the error code and a description of the error. B0 Command from Library controller to robotics controller did not complete in time allotted Reset the device and retry the operation. his comment is here

The text after the main error code (Robotic controller generic problem in this example) is the text description for the error code. Thank you! View library and drive error logs. A0 Sled range of motion out of specification NOTE: Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive.

He Cannot Initialize Barcode Reader Code 80 01

Thank you! Dmitriy 2016-01-10 23:56:16 UTC #2 Please post full code. Upgrading the Library firmware might resolve this issue. Elevator: The part of the robotics assembly that moves in the vertical direction.

HE designates a hard error. Start of content Hewlett Packard Enterprise Support Center Product SupportSearch HPE Support CenterDownload optionsDrivers & softwarePatch managementSoftware updates & licensingDiagnostic passwordsTop issues & solutionsTop issuesMost viewed solutionsTroubleshoot a problemAdvisories, bulletins & Remove the magazine and check for issues such as a tape label preventing the mailslot from opening. He Sled Position Not Found Code 9b 37 The STOP sign icon and the word Crit before the event ID also indicate a hard error.

I am using SimpleTimers. // Managing "Modes" For Xbox, etc. If the problem continues, contact HP support. Run the wellness test. 90 Ends of elevator movement not in expected range Run the wellness test 91 Ends of rotation movement not in expected range Run the wellness test. The event ID is the number on the header line, 0x006E in this example.

while (Blynk.connect() == false) { // Wait until connected } // This will print Blynk Software version to the Terminal Widget when // will log messages here, test code functional terminal.println(F("Blynk He Elevator Blocked Code 8b 26 Power cycle the device and try again. If this error was caused by a manual magazine removal, replace the magazine and try the operation again. Ensure that there is nothing obstructing the gripper.

Msl4048 Error Codes

Run the wellness test. To generate and view a report or support ticket from L&TT, perform the following steps: In the L&TT By Product or By Connection tab, select the device from the device list. He Cannot Initialize Barcode Reader Code 80 01 Generate a detailed support file that can be e-mailed or faxed to the support representative for analysis. He Elevator Blocked Error During Move Elevator To Scan Position Code 8b 26 The error log contains a list of all errors, with a separate row for each error.

To run the wellness test from the OCP, see the Running tests (Support > Run Tests) section in Operator Control Panel (OCP) . B4 “Tape in gripper” sensor did not report the expected value Remove the magazines and inspect them for a stuck tape. Drive error codes Error code Description 01 Drive broken 02 Temperature exceeds limit 03 Tape error 04 Cleaning cartridge is expired 05 Drive needs cleaning 06 Library lost communication with the Either void setup() { ... } either void setup() { ... } hackmanj 2016-01-11 00:07:19 UTC #6 You make it look easy, thanks very much, I moved it between setup and He Slider Blocked Error During Second Slider Movement Code 8a 63

The main error code (0x83) is displayed in parenthesis as the Global error code. C1 Telnet interface initialization failed Check the network cable. Slider is the part of the robotics assembly that plunges in and out for get and put operations. Figure 3: Critical event details The time stamp is in the format hours : minutes : seconds.

If the device was moved, verify that each of the tape cartridges is properly seated in a magazine or drive. 8D Sled obstructed If this error occurs on the first power-on Msl2024 Error Codes View detailed configuration, identification, inventory, and drive information for the library. Here are some terms that you would encounter in the table below (Main error codes): Gripper: The part of the robotics assembly that pinches media in order to grip it.

top Provide feedback Please rate the information on this page to help us improve our content.

Also access error information from the Support sub-menu item, see Viewing logs (Support > View Logs) . If the failure remains with the same slot, the magazine may be at fault. The HP Library & Tape Tools diagnostic provides an intuitive graphical user interface with integrated context-sensitive help. Mechanical Block Code 8d 07 Ibm Run the Wellness Test 8A Slider obstructed NOTE: Slider is the part of the robotics assembly that plunges in and out for get and put operations. 8B Elevator obstructed NOTE: Elevator

Very helpful Somewhat helpful Not helpful End of content United StatesHewlett Packard Enterprise International Start of Country Selector content Select Your Country/Region and Language Click or use the tab key to Ensure that nothing is obstructing the gripper. Contact technical support. The wellness test exercises all robotic movements and checks the status of the electrical components and communication.

sub-code indicates which fan is affected. Sled: The part of the robotics assembly that moves the robot towards the OCP or back towards the drive. Lichtsignaal 2016-01-11 05:29:43 UTC #8 You need to put it outside anything. If the device was moved or shipped with tape cartridges in the magazines, verify that the cartridges did not come out of the magazines to obstruct the drive.

For example: 24/06/05 01:48 D7 50 System Error where: 24/06/05 = date in the format DD-MM-YY 01:48 = hours in 24h clock format. Example: On the RMI error log, an error entry will be displayed as: 05.11.09 13:24:23.02 LIB/ERR, 80 9B 37 31 --- Robotic Failure. 05.11.09 = the date (YY.MM.DD) 13:24:23.02 = the If there is a tape in a drive, replace the magazines and run the Force Tape Eject operation. sub-code 00: drive sled #1, sub-code 01: drive sled #2 NOTE: Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive.

Sign-in Register Site help Solutions Transform to a Hybrid Infrastructure Protect Your Digital Enterprise Empower the Data-Driven Organization Enable Workplace Productivity Cloud Security Big Data Mobility Infrastructure Internet of Things If not successful, attempt a different upgrade method, such as the RMI or L&TT. Sub-code 01:drive sled #2. F0 Drive exceeded temperature specification Check ambient temperature to ensure that it is within operating specifications.

The log shows the Date/Time, Code, and Description. Clean the drive. Explanation of error codes OCP errors Error codes are displayed in pop-up messages when an error occurs during an operation that is initiated from the operator control panel. Once I get the command structure down I can build out everything I need however I keep hitting a wall when I follow examples I've find elsewhere on this community for

More details will also show warning and configuration events. The sub-code indicates the affected fan. F5 Time allotted for drive unloading exceeded Retry the operation. Check that the network configuration is correct.

Check that the network configuration is correct. The support ticket and report contain the same information. Critical events are designated with a STOP sign icon. Check if the fan is operational and not obstructed F0 Drive exceeded temperature specification Check ambient temperature conditions and fans F1 Library controller lost communication with the drive Re-seat the tape

© Copyright 2017 gatoisland.com. All rights reserved.