Home > Error Codes > Bcr Conrol Initialize Error

Bcr Conrol Initialize Error

Contents

Cookies help us deliver our services. If the device was moved, verify that each of the tape cartridges is properly seated in a magazine. 8A Slider obstructed Run the wellness test. top Error sub-code descriptions Robotic error sub-codes The table below (Robotic error sub-codes) lists the robotic error sub-codes. The text description in the header (robotic controller error in this example) is the simple text description of the main error code. http://gatoisland.com/error-codes/bcr-control-initialize-error.php

If this error was caused by a manual magazine removal, replace the magazine and try the operation again. If the device continues to fail, contact HP support. If the failure follows the tape cartridge, the tape cartridge may be at fault. Inspect it for damage.

He Cannot Initialize Barcode Reader Code 80 01

Very helpful Somewhat helpful Not helpful End of content United StatesHewlett Packard Enterprise International Start of Country Selector content Select Your Country/Region and Language Click or use the tab key to If this error occurs with sub-code 43, a magazine could be misaligned. Slider: The part of the robotics assembly that plunges in and out for get and put operations.

Device error sub-codes Error code Description 81 Drive wake up failed 88 Error accessing slot status 90 Robotic load not reached Cartridge Present sensor 91 No activity after Load command 92 See the Force ejecting a drive (Support > Force Drive Eject) section in Operator Control Panel (OCP) . Sled: The part of the robotics assembly that moves the robot towards the OCP or back towards the drive. He Sled Position Not Found Code 9b 37 B1 Robot controller reported format error on command from Library controller Reset the device and retry the operation.

But your tape drive has likely a problem and need to be replaced. Msl4048 Error Codes C1 Telnet interface initialization failed Check the network cable. The message shows the error code and a description of the error. Not the answer you're looking for?

Critical events are designated with a STOP sign icon. He Elevator Blocked Code 8b 26 Clean the drive. The text after the error sub-code (Robotic: connection to slave robotic failed in this example) is name of the component followed by the text description of the error sub-code. The event ID is the number on the header line, 0x006E in this example.

Msl4048 Error Codes

For example: 8D 52 Mechanical Block The error log contains a list of all errors, with a separate row for each error. Attempt the Force Tape Eject process. He Cannot Initialize Barcode Reader Code 80 01 It can be downloaded free of charge from www.hp.com/support/TapeTools . He Slider Blocked Error During Second Slider Movement Code 8a 63 Shi,Hyoung Joong Kim,Fernando P√©rez-Gonz√°lezLimited preview - 2014View all »Common terms and phrases2D code accuracy algorithm attacks authentication binary bit rate broadcaster calculated codeword component computational dataset DCT coefficients decoding decryption denotes

For example, 1:00 pm is 13:00.D7 is the main error code50 is the error sub-code top Finding error code information on the RMI You can find error codes on the RMI Next "clean up" I will do just that. HE designates a hard error. Run the wellness test. 90 Ends of elevator movement not in expected range Run the wellness test 91 Ends of rotation movement not in expected range Run the wellness test. He Elevator Blocked Error During Move Elevator To Scan Position Code 8b 26

I usually put it above loop() function, not in setup, not in loop, just as standalone function. -edit Too late, lol Home Categories FAQ/Guidelines Terms of Service Privacy Policy Powered by Library error sub-codes Error Code Description 81 81 Drive wake up failed 88 Error accessing slot status 90 Robotic load not reached Cartridge Present sensor 91 No activity after Load command Main error codes Error code Description Details and solution 80 Cannot initialize bar code reader Power-cycle the unit and retry the operation. 81 No response from bar code reader 82 No Run advanced diagnostic tests, including connectivity, read/write, media validation, and testing the functionality of the library.

Re-seat the tape drive to ensure a good connection to the device. Hp Tape Library Error Codes top Main error code descriptions Main error codes Error Code Description Details and Solution 80 Can not initialize bar code reader Power-cycle the unit and retry the operation 81 No response Click the Health button on the main toolbar to generate and display a standard report or click the Support button on the main toolbar to display the Support screen for additional

The main error code (0x83) is displayed in parenthesis as the Global error code.

Run the wellness test. 8E Ends of gripper movement not in expected range Run the wellness test 8F Ends of slider movement not in expected range Early firmware versions were not Were slings used for throwing hand grenades? If the device was moved or shipped with tape cartridges in the magazines, verify that the cartridges did not come out of the magazines to obstruct the drive. Mechanical Block Code 8d 07 Ibm B5 Robotic controller not responding to command from Library controller Reset the device and retry the operation.

Check that the network configuration is correct. Thank you! The log entries are displayed in order of most recent to oldest. Insert a USB flash drive into the USB port on the rear panel and then from the OCP, select Download support ticket to USB.

Unless otherwise noted in the troubleshooting document, try to resolve the error by cycling power to the library and retrying the last operation. Please ask the forum!If you feel this was helpful please click the KUDOS!

© Copyright 2017 gatoisland.com. All rights reserved.