Home > Error Codes > Balboa Controls Error Codes

Balboa Controls Error Codes

Contents

All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 30 Days, but some Spa Brands or Models may be Different. Sundance Spas ILOC = Interlock failure - possible pump or ozone spike FLO = Pressure switch malfunction or Flow switch malfunction (system specific) Hold = Panel buttons pressed to many times Press "Mode" Button to Clear Message. Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1. have a peek here

Closed Slice Valve.7. If water is flowing from the circ pump outlet, proceed to test all the other pumps.If the Circ Pump is primed, or if you Do Not have a Circ Pump, then:- If there is Now a Message Other than a "rtC" or "RTC FAILURE" Real Time Clock Error Message, that Message will Now have to be Diagnosed. ToE = Time out error.

Balboa Spa Control Error Codes

No Automatic Functions will turn ON during this time, and the Heater will Not Start. There is Not enough Water in the Heater to Start it. Check for clogged filter. Sensor plugged into jack A is not working.

Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature. --- = "Watchdog". dr = Inadequate water detected in heater. FLO = Flow Switch (heater is deactivated. Balboa Controls Manual Register a new account Sign in Already have an account?

Clean and Condition Spa Cover per Manufacturers Instructions. Do not enter the spa. Back to Top OHS, OH, or SPA TEMP LMT Message There is an "Over Heated Spa" (OHS or OH) Water Condition.One of the Water Temp Sensors has detected 110°F (43.3°C) Incoming Switch closed while pump is deactivated.

Wait 4 Minutes or Press any Temp Related Button to Exit Priming Mode to Normal Operation.Note: On some Early VS and GS Systems (prior to Version 23) equipped with a "Mode" Balboa Controls Troubleshooting If the Spa with the "SF" Safety Fault Error Message has a pump suction blockage switch, Select "Spas with Pump Suction Blockage Switch" Below. The Standard in Economy Mode allows the System to Heat the Water when the Jets are being used between Filter cycles, while in the Economy Mode. Loading...

Balboa Vs501z Error Codes

OH = Overheating, water over 112° F. Transcript The interactive transcript could not be loaded. Balboa Spa Control Error Codes Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... Balboa Vs500 Error Codes Thanks in advance for any help anyone can offer.

keysthinking 49,011 views 2:25 How to Diagnose and Repair Your Hot Tub Heater | Arctic Spas - Duration: 9:09. navigate here The Sensors are Possibly Out of Sync with Each Other, or Not Indicating Close to the Same Temperature at Both Sensors. dr = Inadequate water detected in heater. Install a New Filter Cartridge per Manufacturers Instructions. Balboa Hot Tub Error Codes

  1. Published on Mar 27, 2012Troubleshooting Balboa Legacy Control Systems (Non M7).
  2. Back to Top SLP or SL Message SLP or SL MessageIf the SLP or SL Message is Alternating with the Water Temperature on the Display, the Spa is Operating in the
  3. If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1.
  4. Select "Message Other than CrC or CHKSUM FAIL" Below.
  5. This Mode allows the User to Replace or Clean a Pressure Side Filter Cartridge without Equipment turning ON unexpectedly.
  6. Low Water Level.2.
  7. Contact your Dealer or Service Organization to check the Switch Numbers or Setting Values Displayed, and Correct as Necessary to Match the Equipment in the Spa System, or Continue for a
  8. If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1.
  9. You Must Press Any Button to Reset when Water is below 108°F (42.2°C).
  10. No action is necessary.

SESH = Sensor short, nonfunctional. PSoL = Pressure switch open with low pump. Back to Top SnA, SA, or SENSOR A SERVICE REQD Message "Sensor A" (SnA or SA) is Not Operating Correctly.The Sensor Connected to the "Sens.A" Connector on the System Board may Check This Out Sign in to report inappropriate content.

About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! Balboa Fault Codes this information is being provided for informational purposes only. OHS = Overheat.

Too Many Closed Jets.6.

The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles. Press "Mode" Button to Clear Message. Press any "Cool", "Warm", or "Temp" Button to Exit Priming Mode.3. Balboa Spa Error Codes Heat Related Pump Not Primed.

If alternating with temp, may be temporary condition. You can often determine the make of the control system by looking inside the spa's equipment area. Like the name says, it was quite easy to install." James Hirsch Buffalo, NY Balboa is a trademark of Balboa Instruments - Manufacturer of Control Systems for Spas Get http://gatoisland.com/error-codes/bd2-sql-error-codes.php OHH = Overheat.

Do not do this more than 5 times. After about 45 Seconds, Check for Error Messages on the Topside Panel Display. This is Not an Error Message. Too Many Closed Jets.6.

Heat Related Pump Not Running.8. Back to Top rCO or CLEAN COVER Message Time to Clean "Cover Reminder" (rCO).Appears Every 180 Days*. Spa has shut down. Have you taked the filter out and reset the spa to see if went away....

Back to Top rdr or DRAIN WATER Message Time to "Drain Spa Water Reminder" (rdr).Appears Every 90 Days*.

© Copyright 2017 gatoisland.com. All rights reserved.