Home > Error Code > Balboa Error Code Sl

Balboa Error Code Sl

Contents

Your cache administrator is webmaster. SE = Spa operating in Standard-in-Economy Mode. Low Water Level.2. HOT = Circuit Board temperature has exceeded acceptable limit. http://gatoisland.com/error-code/balboa-error-code-oh.php

HFL = Substantial difference between temperature sensors detected. Couldn't have asked for more. Check for Extended Pump Operation or High Ambient Temp, or contact your Dealer or Service Organization.Spa Water Cool Down• In order for the Spa Water Overheat Error Message to Automatically Reset Low speed pump and heater will activate until spa reaches 65°F.

Balboa Spa Sl Code

System will restart when temp. This turns on pump 1, and also turns on the circ pump.- Verify that both pump 1 and the circ pump are running and that water is flowing out of both Sn3 = Open or shorted sensor ( heater disabled). Check for proper spa water level and ensure pump is primed.

  1. Try Turning the Power OFF and back ON again, or contact your Dealer or Service Organization.1.
  2. Pumps and Blower can be turned ON and OFF to Remove any Air from the Heater.
  3. OH = Over heat.
  4. Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F.
  5. If there is Now a "rtC" or "RTC FAILURE" Real Time Clock Error Message, contact your Dealer or Service Organization.

If display shows only this message (blinking) spa is shut down.HFL = Substantial difference between temperature sensors detected. Please enter a valid email address. Back to Top rtC or RTC FAILURE Message The "Real Time Clock" (rtC) Cannot be Read.At Power-Up, the System Board Real Time Clock could Not be Read. Balboa Hot Tub Turn Off Economy Mode The email address entered is already associated to an account.Login to post Please use English characters only.

If there is Now an Error Message, select Message Other than PSt or Persist Fail below.No Error Messages3. Sensor plugged into jack A is not working. If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1. Back to Top gFI or GFCI FAILURE Message The Control System Could Not Trip the "GFCI" (gFI).The spa has determined that a GFCI is NOT properly installed in the circuit providing

After about 45 Seconds, Check for Error Messages on the Topside Panel Display. Balboa Spa Control Manual If the Error Message has Not Cleared, the Spa Water is still too Hot to Continue Testing.• Either Wait for the Spa Water to Cool Below 108°F (42.2°C), or Exit Now Aquarium PartsBath PartsPool PartsSpa PartsWhite GoodsClearance Items (Bath/Spa) Dealer/Tech ApplicationWarranty InformationProduct ReturnsBack Ordered ProductsDownloads SectionQuestions? It may be possible for a stuck relay to free itself after the power cycle, but the spa cannot clear the the HOt message without starting up in Test Mode first.

Balboa Sns Error Code

Contact your Dealer or Service Organization. Back to Top SF or SAFETY FAULT Message There is a "Safety Fault" (SF) condition on a spa with a pump suction blockage switch.On a spa with a pump suction blockage Balboa Spa Sl Code There is Not enough Water in the Heater to Start it. Balboa Error Codes Hot Tubs Sn1 = Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated).

Do not use spa when temperature is flashing or the OH message is displayed. http://gatoisland.com/error-code/099-error-code.php Other issues that can cause these error codes one or more of the service valves is not open up all the way. Failure to properly service or install spa related components can result in serious injury or death. OH = Overheating, water over 112° F. Balboa Spa Error Codes

The jets stopped working and the 9/30/2016 9/30/2016 Billy About how should the motors and heaters in a spa last. Dream Maker Hot Tubs OH = Overheat 108° F, spa is deactivated. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2. Check This Out The Current Water Temperature is "Unknown" (- - - or - -) while in Economy or Sleep Mode.

If your spa is not overheating and you are getting the above error codes then a couple of things need to be investigated. Balboa Hot Tub Troubleshooting Spa has shut down. Install a New Filter Cartridge per Manufacturers Instructions.

Contact qualified service technician.

If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1. No action is necessary.I CE2 = Freeze protection. Click "Add" to insert your video. Balboa Hot Tub Codes F8 For information regarding repairs click here.

Rare system error. Could indicate a flow problem. Read our FAQ! http://gatoisland.com/error-code/005-122-error-code.php dr = Inadequate water detected in heater.

Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2. Wait 4 Minutes or Press any Temp Related Button to Exit Priming Mode to Normal Operation.Note: On some Early VS and GS Systems (prior to Version 23) equipped with a "Mode" One sensor has detected 110ºF.Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message).

Freshfield, Liverpool, UK This expert is wonderful. Back to Top SLP or SL Message SLP or SL MessageIf the SLP or SL Message is Alternating with the Water Temperature on the Display, the Spa is Operating in the If the Spa with the "SF" Safety Fault Error Message has a pump suction blockage switch, Select "Spas with Pump Suction Blockage Switch" Below. All Pumps and Blower are ON for at least 4 Minutes After Temp is 45°F (7.2°C) or Above at the Sensors, or when the Aux Freeze Switch Opens.

Entire system is disabled. If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1. Brett Aqualine OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° F FL = Pressure switch failure EO = Shorted temp sensor E1 = Open temp Blocked Suction Fitting.3.

drops. Rare system error. Press Any Button other than "Jets 1" to Exit Drain Mode and Standby Mode, and Return to Normal Operation. If there is Now an Error Message, select Message Other than CFEor CONFIG ERROR below or contact your Dealer or Service Organization.No Error Messages:The "CFE" or "CONFIG ERROR" Configuration Error Appears

Select "Message Other than CrC or CHKSUM FAIL" Below. The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles.

© Copyright 2017 gatoisland.com. All rights reserved.