Home > Bit Error > Bit Error Rate Too High Cisco Mds

Bit Error Rate Too High Cisco Mds

Comment Submit Your Comment By clicking you are agreeing to Experts Exchange's Terms of Use. This site is available to the public. This port is connected to my storageFollowing are the details of the switch and Config.Software  BIOS:      version 1.0.21  loader:    version N/A  kickstart: version 6.2(7)  system:    version 6.2(7)  BIOS compile time:       01/27/14  If the SFP is to be replaced, please review and follow article 14001.NOTE:It is possible to issue, under conf t > interface > switchport ignore bit-errors, to ignore the bit-error threshold, http://gatoisland.com/bit-error/bit-error-rate-too-high-cisco.php

Solved! Re: bitErrRTThresExceeded + Cisco DS-C9509 conor.a.mcmahon Jan 15, 2014 7:27 AM (in response to RRR) For the error reported in the initial thread you can refer to the following article for Explanation Recommended Action No action is required. Check for an environmental cause.

Introduced Cisco MDS SAN-OS Release 1.2(2a). By default, the threshold disables the interface.Resolution:Fix:1. Error Message (Error disabled - bit error rate too high).

To print the manual completely, please, download it. No operation should be performed on either port until they are both added or deleted. Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family OL-15956-01 Previous page Next page 1...268269270271272 Also See for Cisco AJ732A - Cisco MDS 9134 Fabric Switch We checked with fabric analyzer, but problem is very periodic and between bad periods it works OK: 0 Question by:mativare Facebook Twitter LinkedIn Google LVL 1 Best Solution bymativare It is

I haven't connected the switch to the blade yet.... 0 Kudos Reply Grayh Trusted Contributor [Founder] Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Introduced Interface has been configured to be administratively down. Unanswered Question Ninad Thakare Jun 29th, 2014  Hi,I have a Cisco 9148 switch, from which one port goes to "Error Disable" state even after shut-noshut. First we need to remind … Storage Windows Signature Collisions Article by: Lee Ever notice how you can't use a new drive in Windows without having Windows assigning a Disk Signature?

fc1/1 is down (Error disabled - bit error rate too high) Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN) Port WWN is 20:01:00:0d:ec:68:80:00 Admin port mode is I.e if you wanted to determine if its a problem with the cable/ SFP/ the physical portbalde or attached device itself..https://support.emc.com/kb/8050 Its matching primus number is emc132384. Ultimately, prevent IP theft, fraud, and cybercrime.Explore products and solutions from RSA.Visit RSA.comOverviewEnterprise Network HardwareSwitchesRouters and Wireless NetworkingOverviewDocumentumLEAPInfoArchiveOverviewDell LaptopsDell DesktopsDell Thin Clients and VDI ProductsNo results foundNo results foundMODERN DATA CENTERGet occasional high error rate, GIBC and cables replaced.

Actions More Like This Retrieving data ... Events Events Community CornerAwards & Recognition Behind the Scenes Feedback Forum Cisco Certifications Cisco Press Café Cisco On Demand Support & Downloads Community Resources Security Alerts Security Alerts News News Video but couldn't find much 0 Kudos Reply Grayh Trusted Contributor [Founder] Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎12-18-2008 The comments are moderated.

You probably already did this, create a log containing the data, time, and duration, of the occurrences. 0 LVL 30 Overall: Level 30 Storage 28 Message Active 5 days ago http://gatoisland.com/bit-error/bit-error-rate-too-high.php Re: bitErrRTThresExceeded + Cisco DS-C9509 RRR Jul 27, 2009 2:11 AM (in response to Heather) I always call this port state the "error disabled" state. Introduced PORT-5-IF_DOWN_BIT_ERR_RT_THRES_EXCEEDED: Interface [chars] is down The port has detected a bit error rate too high in frames received from attached device. The content is provided for informational purposes only and is not meant to be an endorsement or representation by Cisco or any other party.

Connect with top rated Experts 7 Experts available now in Live! Learn More About Cisco Service Contracts Information For Small Business Midsize Business Service Provider Executives Industries Automotive Consumer Packaged Goods Education Energy Financial Services Government Healthcare Hospitality Life Sciences Manufacturing Materials The other end SFP was faulty.Thanks, Brgds,Ninad See More 1 2 3 4 5 Overall Rating: 5 (1 ratings) Log in or register to post comments ActionsThis Discussion 0 Votes Follow Shortcut http://gatoisland.com/bit-error/bit-error-rate-testing-cisco.php CISCO support cannot say any.

Join our community for more solutions or to ask questions. This tool uses JavaScript and much of it will not work correctly without it enabled. Please type your message and try again. 2 Replies Latest reply: Jan 15, 2014 7:27 AM by conor.a.mcmahon bitErrRTThresExceeded + Cisco DS-C9509 Heather Jul 22, 2009 1:07 PM hello from novice

Bug Details Include Full Description (including symptoms, conditions and workarounds) Status Severity Known Fixed Releases Related Community Discussions Number of Related Support Cases Bug information is viewable for customers and partners

Acclaimed Contributor [Founder] Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎12-18-2008 04:20 AM ‎12-18-2008 04:20 AM Re: connecting BL860c Sign up! You can not post a blank message. Locate partners—or learn about becoming one.Find EMC PartnersEMC Business Partner ProgramBecome an EMC ResellerPartner CommunityPartner PortalRSA PartnersDell PartnerDirectContact UsPartner with EMC today.Live ChatContact SalesCall 1-866-438-3622Call 1-866-438-3622Company InformationKeep up with the news,

The Shortest and Easiest explanation ever! errors like that: vent Description:2008 Feb 20 11:18:35 K-far1 %PORT-5-IF_DOWN_BIT_ERR_RT_THRES_EXCEEDED: %$VSAN 1%$ Interface fc4/7 is down (Error disabled - bit error rate too high) Lot of GIBC and cables etc are Report Abuse Like Show 0 Likes (0) Go to original post Actions More Like This Retrieving data ... More about the author Opinions expressed here and in any corresponding comments are the personal opinions of the original authors, not of Cisco.

Explanation Recommended Action Check the attached device and replace it if needed. Please type your message and try again. 0 Replies Latest reply: Oct 13, 2014 10:34 PM by fredrickchisanga Error disabled - bit error rate too high on MDS switch fredrickchisanga Oct

© Copyright 2017 gatoisland.com. All rights reserved.