If there is an error message on the screen identifying a problem with a device (such as the floppy drive or hard drive), check the device to make sure it is If the operating system is attempting to boot from a device (such as the floppy drive or optical drive), check system setup to ensure the boot sequence is correct for the Then, detect and initialize the video adapter BIOS Sign On - This will start showing information about logo, processor brand name, etc... Deep discharge occurs when a battery is left unused for extended periods of time. http://gatoisland.com/bios-error/bios-error-4.php
If available, install a working graphics card into your computer. Table of Contents: Diagnostic LEDs for the OptiPlex series (Prior to 2005) Diagnostic LEDs for the OptiPlex Series (2005 to 2009) Diagnostic LEDs for the OptiPlex series (2009 to 2012) Diagnostic HP Notebook PCs - Computer Does Not Start and Emits an LED or Beep Code First steps when a notebook LED or beep code occurs Notebook battery power LED blinks LEDs Your computer's power socket has an LED.
V5.2 refers to the BIOS version. 091096 refers to the date this BIOS is released. Repeat this process for each expansion card installed. After you count the number of blinks, use the chart to identify the error condition, and then see the corresponding section for that error condition below for troubleshooting steps. The codes are not valid for other models.
Power Light State Description Off Power is off, light is blank. By following these steps the BIOS will reach the EFI partition in order to recover the BIOS to the last known good version of the BIOS from the hard drive. Configuration Displays your hardware configuration for the selected device. Optiplex 790 Diagnostic Lights You may have to replace the motherboard, but that is rare. 4-4-1 Your serial ports are acting up.
Contacting HP Customer Support If you cannot find a troubleshooting solution, contact HP Customer Support for further assistance or to have the computer serviced. Hp Bios Error Codes How to install Windows 2000/XP using the onboard RAID • Right after booting off of the Windows cd, you need to push the F6 key when Unplug the AC adaptor from the notebook. Ensure that no special requirements for memory module/connector placement exist.
This does not indicate a fault condition. Optiplex 960 Diagnostic Lights The Support Agent can help you troubleshoot the startup problem. Otherwise, proceed to the next step. Use the following steps to remove and reseat the memory modules: Step 1 - Remove the electrical power To remove all power from the computer and prevent accidental damage to the
Disconnect all peripheral devices and remove all USB devices and media cards. Memory modules are detected, but a memory configuration or compatibility error has occurred. Bios Error Beep Codes Solid Amber Second state of the light at power up. Dell Bios Error Codes Release the Power button and the keys.
Notebook battery power LED blinks The battery power LED indicates the condition of the power supply. More about the author If lights come on then power supply is good. See the section Reseating memory modules in a notebook for more information. If a startup menu opens, use the arrow keys to select Start Windows Normally, then press the Enter key. Ibm Bios Error Codes
If the problem persists, contact Dell. Look at the diagnostic lights for further information. For detailed information on this topic, see HP Notebook PCs - Update Your Computer After Troubleshooting a Problem . check my blog Reseat the memory.
The problem could be that the stick of memory or one of the memory slots has a bad connection. Dell Optiplex 980 Diagnostic Lights Allow one minute for the power to drain. Show all | Hide all Diagnostic LEDs CPU configuration activity or failure; CPU Cache failure LED Pattern State Name State Description Suggested Resolution No Pattern Visible Off System POST complete -
Verify that the CMOS jumper is set correctly. Sequence/pattern Meaning Troubleshooting steps 3 blinks (3 beeps) On-off (1.0 second each) three times, then 2.5-second pause (off). In the BIOS Setup Utility, use the Right Arrow or Left Arrow keys to navigate through the menu selection to locate the Diagnostics . Optiplex 990 Diagnostic Lights See the section Reseating memory modules in a notebook for more information.
If reseating the memory does not resolve the problem, try replacing the memory modules, or contact support for repair due to a possible RAM or system board failure. 3.3 (blink/beep) Caps To enter BIOS during boot up hold down one of the following keys: Hold down the < Del > key Hold down the
Figure : "Shipping mode" blinking LED light To resolve this issue, turn off the notebook, connect the AC power and allow the battery to charge for at least 30 minutes, and If possible, connect a different AC power adapter to verify that the adapter is the problem, or contact HP for support. Plug the AC adapter into the computer. IBM BIOS beep codes Below are general IBM BIOS Beep codes that can occur.
Beeps are emitted from a computer during the boot process when some problem is encountered and can be used to troubleshoot a dead computer. If the computer does not automatically recover the BIOS, perform a BIOS recovery manually by pressing all four arrow keys at the same time to cause the BIOS to go to You'll likely need to get another board. 3-2-4 One of the chips on your motherboard that checks the keyboard is broken. When the boot device list appears, highlight Boot to Utility Partition and press
If the I/O is on the motherboard itself, disable them with a jumper (consult your manual to know which one) and then add an I/O card. 4-4-2 See 4-4-1, but this Help Describes the test and may indicate requirements for running the test. For information on how to restore the BIOS refer to the HP support document: HP Notebook PCs - Restoring the BIOS.