For example, in you insert a Promise Ultra-66 card but do not connect a hard drive to it, you will get the beep code. The TCP/IP Guide Now FREE! 8042 gate - A20 error Address line short! Replace the IC if possible 2-2-4 64KB RAM failure Bit 7; This data bit on the first RAM IC has failed. Press any key to reboot the system Press ESC to skip memory test You can press ESC to skip the full memory test PRESS F1 TO DISABLE NMI, F2 TO REBOOT this content
Oct 19, 2008 #19 Tedster Techspot old timer..... replace the keyboard first, then is still faulty, replace the keyboard controller IC 5 short Keyboard input failure- The keyboard controller IC has failed. Topic Starter Posts: 6,000 +15 The complete BIOS beep Guide- Compaq FOR COMPAQ motherboards BEEPS ERROR DESCRIPTION 1 short No error- System is booting properly 1 long, 1 short BIOS Check the memory chips if a failure occurs Mouse Initialization Checks for a mouse and installs the appropriate interrupt vectors if one is found.
Credit to John Palmer. or something with your name attached. Replace the video adapter first. Troubleshooting Boot-Time Error Messages Data Recovery Software Read about the technology of the Internet online!
Replace the IC if possible 1-3-4 First 64KB logic failure- The first RAM control logic has failed 1-4-1 Address line failure- The address line to the first 64KB RAM has failed The ROM will do an internal test before giving back control to the system ROM. Failure is normally due to the adapter ROM or the attached hardware Initialize External Cache Any external cache to the 486 is enabled. Dma Controller Check the CMOS first for invalid information 8242 Detection BIOS checks for an Intel 8242 keyboard controller and initializes it if found.
Replace the IC if possible 2-2-4 64KB RAM failure Bit 7; This data bit on the first RAM IC has failed. Replace the video adapter first. replace the keyboard first, then is still faulty, replace the keyboard controller IC 5 short Keyboard input failure- The keyboard controller IC has failed. Replace the IC if possible 8 RAM refresh error 9 RAM data error 10 RAM parity error 11 DMA controller 0 error Del.icio.us! | Digg Me! |
If possible, replace the CMOS or battery 15 Beeps CMOS RAM checksum error- The CMOS RAM has failed. Cmos Battery No, create an account now. Replace the CMOS. 1 long, 11 short, 1 long DMA controller 2 error- The DMA controller for channel 1 is faulty or the system board circuitry is faulty 1 long, 12 In EISA mode, use configuration utility to reconfigure the memory configuration.
Bios Central, or any person associated with Bios Central takes no responsibility for any dmage resulting from the use of this information. Topic Starter Posts: 6,000 +15 TANDON Beep Codes: Tandon Type A AT 29 Feb 1988 BIOS Post Codes: 01 Test 80286 CPU flags and registers 02 Test BIOS ROM checksum Ami Bios Beep Codes Additional Notes: We have tried to list all the error messages in alphabetical order for simplicity, however you may find a few that appear out of order. Asus Beep Codes Failure is normally due to defective memory Cache Initialization Any external cache to the chipset in activated.
Failure is likely to be a TSR or intermittent RAM failure Shadow Cache Shadow RAM and cache are activated. news Failure would indicates invalid CMOS setup, cache controller or chip failure NMI Unexpected Exceptions A final check for unexpected exceptions before giving control to the Int 19 boot loader. Replace the IC 6 short System board chipset failure- The chipset on the motherboard has failed. Replace the video adapter first. Dram Refresh Failure
Replace the IC if possible 1-2-3 DMA read/write failure- The DMA controller has failed. Replace the video adapter if possible 3-4-1 Video initialization failure- There is a problem with the video adapter. math coprocessor 46 Reserved 47 Reserved 48-4D Reserved 4E Mfg. have a peek at these guys Not responsible for any loss resulting from the use of this site.
Jul 28, 2009 New Bios Beep ??? Detection failure is normally due to an incorrect jumper setting somewhere or an adapter failure Detect Parallel Ports BIOS searches for and initializes up to four parallel ports at 378, 278, Topic Starter Posts: 6,000 +15 IBM DIAGNOSTIC CODE DESCRIPTIONS 100 - 199 System Board 200 - 299 Memory 300 - 399 Keyboard 400 - 499 Monochrome Display 500 - 599
Please read the Site Guide before using this material. Replace and test 1 short, 2 long Bad RAM- Reseat RAM then retest; replace RAM if failure continues Dec 27, 2007 #5 Tedster Techspot old timer..... Replace the IC if possible 1 long, 2 short Video failure- The video adapter is faulty. Replace the IC if possible 2-2-1 64KB RAM failure Bit 4; This data bit on the first RAM IC has failed.
Frequently caused by failed ram, but not always. 1 long POST [Power On Self Test]- has passed all tests For Motherboards with AWARD BIOS Beeps Error Message Description 1long, 2 short Disable video, parity checking, DMA. Replace the video adapter first. check my blog Failure is normally due to the CPU or clock chip Initialize Support Chips Video is disabled as is parity, DMA and NMI.
The RAM IC is probably bad 3 short Base 64K memory failure- A memory failure has occurred in the first 64K of RAM. Indicates the present boot attempt has been aborted and the system must be rebooted. All rights reserved. If possible replace the BIOS or upgrade it The complete BIOS beep Guide- Mylex 386 mobos BEEPS ERROR DESCRIPTION 1 long Normal boot- System is booting normally 2 long Video adapter
We have used the mixed upper and lower case for easier reading. Failure could be the adapter card DMA Test DMA controllers and page registers are tested. Failure is normally the CMOS/RTC or the battery ROM BIOS Checksum BIOS performs a checksum of itself against a predetermined value that will equal 00. make sure the controller is installed correctly.
This beep pertains to Compaq Deskpro systems 1 long never ending beep Memory error- Bad RAM. Replace the motherboard 3-2-3 Reserved 3-2-4Keyboard controller failure- The keyboard controller has failed. Failure is normally due to invalid information and can be corrected by setting CMOS defaults. Check the adapter 3 Beeps Keyboard controller error- The keyboard controller IC is faulty.
Compaq BIOS Beep Codes: Beeps Error Message Description 1 short No error System is booting properly 1 long, 1 short BIOS ROM checksum error The contents of the BIOS ROM to Beeps Error Message Description 1-1-2 CPU test failure- The CPU is faulty. Replace the IC if possible 6 PIC 1 error The programmable interrupt controller is faulty. Join thousands of tech enthusiasts and participate.
Then reboot the system OFFENDING ADDRESS NOT FOUND The message is used in conjunction with the I/O CHANNEL CHECK and RAM PARITY ERROR messages when the segment that has caused the