Home > Backup Exec > Backup Exec Storage Device Configuration Error

Backup Exec Storage Device Configuration Error

Looks like a Firmware update to the RAID controller is in order but when I last checked with MYLEX a few months ago, none was available. If replacing the tape doesn't work, the problem is most likely related to device drivers or the tape drive itself. How an effective data archiving system can ease backup woes Address test/dev data protection challenges Load More View All Problem solve PRO+ Content Find more PRO+ content and other member only See How to improve Backup Exec's performance.

Troubleshooting hardware-related issues Symantec Backup Exec > Troubleshooting hardware-related issues Introducing Backup Exec Installing Backup Exec Configuring Backup Exec settings and options Managing Source

Examine the services. However, in this case I think this is an unlikely cause, as it used to work before. Load the appropriate Backup Exec tape driver. The device is removed from the computer.

No Yes Did this article save you the trouble of contacting technical support? You can usually clear a VSS writer error by rebooting the machine. Solution The server name must be specified as recommended by Symantec.

  1. What should I do?
  2. Start Download Corporate E-mail Address: You forgot to provide an Email Address.
  3. This applies to all versions of Backup Exec. * If you can see SCSIChanger, and it is properly loaded without errors: * Check the registry keys in section II of
  4. It is a good idea to initially check for updates to the .NET Framework.
  5. To be able to use see a Robotic Library (Changer), Backup Exec needs to have an non-plug-and-play driver called "SCSIChanger" loaded.
  6. No Yes How can we make this article more helpful?

No operations are allowed on the device until it is online again. It is possible that updates have been made to the original version after this document was translated and published. But, when I reboot the server I receive the following message: "Storage device configuration error. Struggling Violin Memory launches two new Flash Storage Platform arrays with improved performance, lower latency and encryption ...

About Us Contact us Privacy Policy Terms of use SearchDataBackup Search the TechTarget Network Sign-up now. We'll send you an email containing your password. Try a new tape that is certified by the hardware manufacturer. On display of LTO Ultrium 2 448 appeared SEQ.

SearchITChannel New SUSE partner program offers product training, rebates SUSE's new channel program offers rebates of up to 30% to partners who train and certify their sales and engineering personnel on... The cyclic redundancy check (CRC) error can be caused by many factors. To place the device online, try the following: Check to make sure the device has power and that cables are properly attached. It occurs when one or more Backup Exec services will not start.

Thoughts? Backup Exec Error 1053: The service did not respond to the Start or Control Request in a timely fashion This is one of the Backup Exec errors that can be caused Confirm that the tape drive is functioning properly. How to complete a disaster recovery plan process without funding There are paths you can take if your organization does not allow for DR plan spending.

Veritas does not guarantee the accuracy regarding the completeness of the translation. this contact form Note: The Hardware Compatibility List is frequently updated with newly supported devices. SCSI controller synchronous negotiation enabled. This code is used by the vendor to identify the error caused.

Then delete them, so there are no tape drives or robots Go to Solution 3 Comments LVL 1 Overall: Level 1 Message Expert Comment by:dylanharrington2007-11-09 When you were installing backup go allin!!! 0 Kudos Reply The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. The following list contains the most common reasons for this error and potential ways to resolve the problem: Contaminated read/write heads of the tape device. http://gatoisland.com/backup-exec/backup-exec-error-device-not-connected.php If the flop doesn't fit...

SearchStorage Virtual Instruments teaches VirtualWisdom NAS expertise Virtual Instruments taps into expertise gained through the Load DynamiX merger to teach its VirtualWisdom analytics products to ... Maybe it got uninstalled by what your colleague did. I recommend downloading and installing the latest device drivers for your tape drive.

The drive containing the backup-to-disk folder is offline.

Use the manufacturer's SCSI setup program to lower the SCSI transfer rate. If the device is a narrow (50 pin) SCSI device, disable wide negotiation. I just need to ignore the error BackupExec displays. The exact method to remove and reinstall the .NET Framework will vary depending on the operating system used.

Check with the controller and backup device manufacturer for the proper configuration for the SCSI transfer rate. This Storage Device Configuration Error Backup Exec 2010 error code has a numeric error number and a technical description. Be sure that Windows operating system properly recognizes the device. Check This Out I have gone thru the symantec veritas website and not been able to find a solution.

Connect with top rated Experts 8 Experts available now in Live! Contact TechTarget at 275 Grove Street, Newton, MA. After making any changes, it is a good idea to reboot the server. Compatibility: Windows 7, 8, Vista, XP Download Size: 6MB Requirements: 300 MHz Processor, 256 MB Ram, 22 MB HDD Limitations: This download is a free evaluation version.

But, when I reboot the server I receive the following message: "Storage device configuration error. Keep in mind that editing the Registry is dangerous; a mistake can cripple Windows and/or your applications. The Storage Device Configuration Error Backup Exec 2010 error is the Hexadecimal format of the error caused. Turn the device on and reboot the server, or stop and restart the Backup Exec services.

The DLT tape drive maintains internal information about the tape on a tape directory track. Launch Data Protection Manager from the deskt… Windows Server 2012 Storage Software Setting the Media and Overwrite Protection Levels in Backup Exec 2012 Video by: Rodney This tutorial will walk an Solved Backup Exec can't see the Robotic Library to add a drive Posted on 2007-11-09 Storage Software Storage 1 Verified Solution 5 Comments 10,334 Views Last Modified: 2013-12-01 Hello, I'm trying Even so, errors do occur.

All the above actives may result in the deletion or corruption of the entries in the windows system files. Also make sure scsichanger.sys is present in c:\windows\system32\drivers. In the interim you can use the older version 5.06 firmware which is archived at the following URL: ftp://ftp.mylex.com/pub/support/archive/extremeraid/ Allan C. You also agree that your personal information may be transferred and processed in the United States, and that you have read and agree to the Terms of Use and the Privacy

Allan C. Sorry, we couldn't post your feedback right now, please try again later. Covered by US Patent.

© Copyright 2017 gatoisland.com. All rights reserved.